|
Page: 1/2 Records: 1 - 18 of 25
|
PHR04 RF Keychain Remote
The PHR04 RF Keychain Remote is programmable to any 2 sequential X10 addresses (requires transceiver). Individual RF components can be added in nearly any combination for customization of each installation. Multiple RF Remotes can transmit to a single Base Transceiver (PAT01). Only one Base Transceiver is needed per addressable letter code (A-P). A second may be added if more than one letter code is used.
$15.95
|
|
Rain8 8 Zone Irrigation Controller
The Rain8 is a full featured, 8 zone irrigation controller that may be linked together to provide a maximum of 256 zones of operation. A must for automating lawn sprinkler systems.
A complete irrigation schedule can be triggered by the reception of a single X10 power line carrier command. With its dual mode capability, each individual zone can be controlled independently if the user prefers. Using a PC and software sold separately, all aspects of irrigation may be controlled locally or even over the Internet*.
$79.95 to $99.25
|
|
Rain8 II 8 Zone Irrigation Controller
The Rain8 II 2-Way Model With the 2-way version of the Rain8, you can determine which irrigation zones are on and which are off. Designed for use with X10-compatible computer interfaces and other devices that can generate the X10 Status Request command. In addition to giving you the power to poll irrigation zones to determine their on/off status, it also allows your computer send a command to the module then check to see if the command was carried out. If not, the computer can automatically send the command again.
$89.95 to $114.50
|
|
RCS TXB16 X-10 Controlled Thermostat
The TXB16 Thermostat functions as a standard thermostat and can be controlled by X10 commands to set specific temperature setpoints and modes for the HVAC system. The leading-edge two part design of the TXB16 consists of a TS16 Wall Display Unit and the TXB16 HVAC Control Unit.
$329.95
|
|
W800RF32 X10 RF Receiver
The W800RF32 family of X10 RF receivers are designed to receive X10 RF signals generated from X10 products: Palm Pad remotes, key chain remotes, Hawkeye motion detectors, and many, many other X10 RF devices. The W800RF32 then sends these commands directly to your computer's serial(RS232)port...
$59.99 to $68.99
|
|
X-10 Pro 15A Single Control Outlet
PA011: Receptacle Modules offer remote control of various appliances and can be used in place of plug-in Appliance Modules for a more professional look.
$16.95
|
|
|
|
X-10 Pro 20A Dual Control Outlet
XPR: Receptacle Modules offer remote control of various appliances and can be used in place of plug-in Appliance Modules for a more professional look.
$21.95
|
|
X-10 Pro 3-Wire Noise Filter
XPF: Direct 3-Wire Noise Filter. Various devices are a source of noise and can interfere with X-10 signals. This Filter wires directly to isolate a specific appliance, such as ceiling fan, flourescent fixture, etc..
$60.95
|
|
X-10 Pro Black Maxi Controller
PHC02: Maxi Controller. Controls up to 16 individual X-10 addresses. "Group" feature allows simultaneous control of multiple addresses. Available in Black only.
$18.95
|
|
X-10 Pro Coupler Repeater Amplifier
XPCR: Coupler/Repeater. Installs at the electrical panel to couple, repeat and amplify X-10 command signals. Recommended in all X-10 installation applications. A "Must Have"
Component.
$129.95
|
|
X-10 Pro Decora Style Switch
XPD3-IW: SP Rocker style X10 switch. Same switch for Single Pole or 3 & 4 way applications. Packaged as BOTH White and Ivory. Includes Cover Plates.
$22.95
|
|
X-10 Pro Dual Floodlight Motion
PHS01: Dual Floodlight Motion Detector primarily acts as a dusk or motion sensor. However, the device is also capable of sending "ON" and "OFF" commands to four devices when it senses motion and four separate devices when it senses dusk.
$44.95
|
|
|
|
|
X-10 Pro Inline Receiver Module
XPFM: Works with resistive loads and inductive loads and offers On Off Only. Use at fixture when no neutral exisits at Light Switch. Responds to "All Lights ON".
$21.95
|
|
|
|
X-10 Pro Passive Phase Coupler
XPCP: Passive Coupler. 1:1 ratio. Installs at the electrical panel to couple both phases of the 220V circuit. Allows X-10 Signal to transmit across both phases. NO Amplification. A Must for all installations. Larger installations may require an XPCR (sold seprately).
$33.95
|
|
|
<< 1 2
>>
|
